Fuel "Y" splitter

Terminal Block

Stock up on all the 33mm main jets you need!

For those running a 33mm, 40mm, or 42mm carburetors with air bleeds rather than air mixture screws, don't get to the track without the jets to make the adjustments you need. Get what you need here!

Carburetor bowl bolts M4-0.7 X 10 socket heads. Sold in sets of four

NGK Spark Plug B8HS

Max Jets for Mikuni 42 and 45mm carburetors. Use to fine tune your carburetor!

CALL FOR ORDER. SELECT SIZES MAY BE UNAVAILABLE.

Get your secondary to primary clutch offset just right with this clutch alignment rod!

Pilot jets sizes 52, 55, 57, 59, and 62. Don't get stuck at the track without the right jets for adjustments. Get what you need!

5/16"- 24 x 6" shockwave secondary threaded rod individual piece.

1/4" Fuel line, Five feet of your favorite color to ensure your junior dragster looks great!

Weld on EGT sensor mount.

Replacement lug nuts for your wheel studs. Sold in sets of three

Left and right 5/16" 24 thread junior dragster rod ends

Are you getting air leaks in your fuel system? Try starting with replacing your 42mm carburetor float bowl O-ring!

Are you getting air leaks in your fuel system? Try starting with replacing your 33mm carburetor float bowl O-ring!

Designed for Jr Dragsters/Go-Karts and other chain drives, Lucas Sprocket & Chain Lube is designed with a specific additive package to prolong the life of sprockets and chains. Fortified with “moly” and other dry film lubricants, you can expect less friction at high RPM’s for less drag and longer component life.

Front cover gasket for 42mm carburetor. If you've gone through your whole fuel system trying to find an air leak? Don't forget to check here!

Top gasket for any 42mm carburetor top.

3/4" ID locking collar.

1-1/4" locking collar. Is your axle wanting to shift? Lock it up with a couple of these and you won't have to worry about it again! Sold individually.

Jr dragster oil fill plugs, available in blue, purple, black, aluminum, and red.

Our easy strap/mount on tail lights come in 5 awesome colors! LED lights are bright and easily seen for max safety. Batteries Included!


Note, if you are racing NHRA sanctioned event, the strap must be removed via a small screw on the rear of the unit, A small hole drilled into your rear shield or other area and the screw replace through the car to permanently mount the light on the car to meet the rule listed on page 39 of the JDRL Rule Book. Using the strap on method is not NHRA legal. Please feel free to call for specific directions.

Standard carburetor bowl plug that fits a 42mm standard bowl and some 33mm bowls.

Shockwave Overdrive roller formulated stronger to withstand the torque of an overdrive setup and heavy packages.  Self Lubricating for smoother transitions. New interior cut design to hold bearing in place to reduce movement.  Sold individually. Sold with washer and nut.

Idle speed adjuster for 33mm Mikuni Jr Dragster Carb.

Rubber Seal for Mikuni HSR42/45 Throttle Valve.

Designed for 28 mm Carburetor

Air filter adapter for a 33mm carburetor.  This adapter is tapered for maximum air flow at maximum velocity.  Get the power you need for more consistent Jr Dragster runs!

If you're looking for something for your junior dragster with maximum filtration and a lot of style, look no further than these bad boys! With 7 colors available you'll be sure to find something to match your jr dragster!

For those of you using air mixture screws rather then air jets. Comes with spring, washer, and o-ring.

Filter for 660 Pro EVAC system. 1.5 inch

1-1/4" Rear axle bearing, sold individually.

Replacement clamp for EGT sensor.

Lucas Oil Slick Mist is a polymer paint gloss intensifier, which can be used on other surfaces such as glass, chrome and vinyl decals. Use Slick Mist as a traditional wax, quick detail spray or spray it on your Jr Dragster between races or rounds! That’s right! Just spray it on a wet or dry surface and wipe it off. Slick Mist out performs the competition and will leave your finish slicker and shinier than any product on the market, with long lasting protection. You and Slick Mist can give any machine an extreme gloss fast!

Replacement needle and seat for your 28mm carburetor.

Idle speed adjuster for 42/45mm Mikuni Jr Dragster Carb.

Throttle butterfly for a mikuni 42mm carburetor.

Idle Cam for a 42mm carburetor. If your having problems with them breaking try taking out the stop screw!

Replacement 42mm carburetor jet needle.

Jr dragster long oil fill plug. Sold with o ring

Jr Dragster Oil Fill Extension. Sold With O-Ring

Genuine Mikuni Fuel Joint for 42/45mm carburetor.

2 pieces of black junior dragster roll bar padding for halo bars.6" long. Fits 3/4" bar diameter. 3/8" thick at your child's site line. SFI 45.1. NHRA Jr dragster Mandatory. EASY INSTALL

Jr Dragster Air Filter Adapter for 42mm carburetor, tapered down to 2 7/16" OD. Compatible with PARTS AAF2716 and AFM514.

Tag your jr dragster parachutes with 1/8th Mile Apparel's amazing quality tags that will last you for years to come. Stand out in the staging lanes.
Sold Individually
Add an additional tag for dual chute system!

Made in the USA

12''x 2''

Air filter 3 1/2" OD 2 7/16 ID AT 20 degrees

Evac filter 1.5" ID. 3" tall x 3" wide.

Hard coated black rear axle junior dragster  bearing cassette. SOLD INDIVIDUALLY

Secondary springs for your polar jr dragster setup! Red spring is heavy duty and yellow is standard.

Floats designed for 33mm Carburetor

Shockwave Overdrive Purple Spring

Needle and seat for 42mm or 33mm carburetor.

If your Mikuni Floats weigh more than 16 grams then you need new ones!   Mikuni Floats for 42mm Jr Dragster alcohol carburetor.

Dual cone air filter 3 inch. Reinforced for jr dragster use (Available with adapter for 2.5in.)

Custom Sized Throttle Cable just for Jr Dragsters. No more cutting and excessive looping around of extra cable.  Barrel end fits perfect in your Mikuni carburetor. Comes with adjuster duel screw that fits aftermarket billet carburetor tops.

This tail light casing is designed to carry the ever so popular circular tail lights seen on many junior dragsters  today. These casings can be mounted right to your jr dragster firewall! Lights Included.

ButlerBuilt Crew Gloves.

Lucas Non-Chlorinated Brake Parts Cleaner is manufactured with the highest quality components to provide excellent performance without leaving any residue. It effectively removes brake fluid, grease, brake dust, and other contaminants from brake linings, pads, cylinders, springs and drums. Professional strength and powerful spray pattern improves performance of the product. For use on all ABS, disc and drum brakes. Quiets noise associated with excessive brake dust.

Lucas Non-Chlorinated Brake Parts Cleaner is VOC compliant in all 50 states and label is compliant with GHS regulations.

To remove brake fluid, grease, dust and other contaminants, spray liberally onto areas to be cleaned. Use in well ventilated area and wear safety glasses. Protect rubber, painted surfaces and plastic from overspray. Do not use on polycarbonate or styrenated plastics.

Kenda Kwest 16" x 1.50" Tire used on jr dragster front wheels

660Pro Parachute tag by 1/8th Mile Apparel is high quality and durable! Great addition for the final touches of your Jr dragster. Dual Sided

33mm Intake flange with small bolt pattern 2.312".

Genuine Mikuni T.V. Sealing Ring for HSR42/45mm throttle valve

JrDragster Dial Board. Offer 4 digit and 3 digit. NO MOUNT.

1-1/4" Keyed Sprocket hub for jr dragster and karting.

33mm Intake flange with wide bolt pattern 2.900".

MCP standard brake pads. Sold as Set.

Specially formulated low resistance rollers for standard shockwave primary clutches. Make sure you get the best performance out of your 8.90, 11.90, and 13.90 shockwave setups! (Not recommended for OD shockwave). Sold in sets of three. Sold with washers and nuts.

Single Piece Black junior dragster roll bar padding. Fits 1"-1 1/8" bar diameter. 3/8" thick at your child's site line. SFI 45.1. NHRA Mandatory. EASY INSTALL

See Jr Dragster Roll Bar Padding Kit (SFI 45.1)

Tired of losing jets? Well this is jr dragster jet block is for you! Next time you need to make a quick jet change on your jr dragster you'll know all your jets will be in one place on these boards! There is even slots for air bleeds!
Available for Max jets AND Mikuni Jets.

Jr Dragster front sprocket for 415 set up. Center Drive for added strength.

Jr Dragster Ceramic Starter Nut Bearing

Jr Dragster Jackshaft. Jackshaft spacers not included

Case Of 6.Designed for Jr Dragsters/Go-Karts and other chain drives, Lucas Sprocket & Chain Lube is designed with a specific additive package to prolong the life of sprockets and chains. Fortified with “moly” and other dry film lubricants, you can expect less friction at high RPM’s for less drag and longer component life.

Air Filter 5 1/4" OD x 6" x 2 7/16" ID
20 Degree
Tapered

Standard drive belt (.790") by 660 Pro that is formulated in a special compound to minimize slip to provide better launch and consistency. For use on all standard Shockwave and Polor Max Setups.

Billet sprocket hub for a keyed axle.

Shockwave Overdrive rollers formulated stronger to withstand the torque of an overdrive setup and heavy packages.  Self Lubricating for smoother transitions. New interior cut design to hold bearing in place to reduce movement.  Sold in sets of three. Sold with washers and nuts.

Rubber carburetor flange for 42mm carburetor.

With today's wild cut Jr Dragster front wheels be sure to hold the beam and avoid undeserved red lights! Our light guard holds the beam for as true of a light as possible. Be safe, not sorry!
Multiple colors available. Color you want not listed? Give us a call or email!

Jr Dragster Drive belt (.850") by 660 Pro that is formulated in a special compound to minimize slip to provide better launch and consistency for overdrive and outlaw clutches.

Lucas Penetrating Oil loosens rusted-on nuts and bolts finding its way between the tiniest of crevasses between metal parts and lubricating them. Lucas Penetrating Oil is fortified with powerful corrosion inhibitors and wetting agents that insure protection to parts exposed to the elements. Evaporation is slow, leaving a tenacious film that fights water and corrosion.

Use on: nuts, bolts, hinges, bearings, sliding doors, bicycle chains and a million other uses around the home, garage, shop and office! Stops those annoying squeaks.

Equipped with a locking pop-up tube and 360° applicator - use in any position even upside down; the product goes where you want to and you never lose the straw.

A wider Jr Dragster Drive belt (.875") by 660 Pro that is formulated in a special compound to minimize slip to provide better launch and consistency for overdrive and outlaw clutches.

Round Mikuni fuel pump (DF52) for Jr Dragster. Under "ADD" you can add the rebuild kit to your order as well!

120 links 35 Regina gold Junior Dragster chain, master link included.

Replacement Cam following rollers for a shockwave and terminator jr dragster secondary clutch. These are our own JDP custom black rollers designed for the least amount of friction possible. Make your secondary shift smoothly for more consistent runs.  They come prepacked with bearing grease sold in sets of three.

Jr Dragster air filter, 5 1/4" OD x 5" x 3" ID @ 20 degree

Lucas Non-Chlorinated Brake Parts Cleaner is manufactured with the highest quality components to provide excellent performance without leaving any residue. It effectively removes brake fluid, grease, brake dust, and other contaminants from brake linings, pads, cylinders, springs and drums. Professional strength and powerful spray pattern improves performance of the product. For use on all ABS, disc and drum brakes. Quiets noise associated with excessive brake dust.

Lucas Non-Chlorinated Brake Parts Cleaner is VOC compliant in all 50 states and label is compliant with GHS regulations.

To remove brake fluid, grease, dust and other contaminants, spray liberally onto areas to be cleaned. Use in well ventilated area and wear safety glasses. Protect rubber, painted surfaces and plastic from overspray. Do not use on polycarbonate or styrenated plastics.

High output Briggs coil

5 foot box of 415  Regina Gold chain.  This chain is a true roller with the least resistance possible. Out performs 35 chain in consistency and durability.

This billet 33mm jr dragster carburetor top is a great way for your junior to look PRO. Comes tapped for clamp kit kit.

Do you want to get the best performance out of your Shockwave clutch? Try these nylon rollers with ceramic bearings inserted! These are the most free rolling rollers you will find!

Designed for Jr Dragsters/Go-Karts and other chain drives, Lucas Sprocket & Chain Lube is designed with a specific additive package to prolong the life of sprockets and chains. Fortified with “moly” and other dry film lubricants, you can expect less friction at high RPM’s for less drag and longer component life.CASE SHIPS FREE

Prevent Tearing. New full pull tab design for easy removal. Made of 1000 denier Cordura nylon material. Developed by Dupont, this is the same material used in United States military gear. Don't be mislead by others claiming denier of a lesser count or some who bill out Condura instead of Cordura. These jr dragster covers are simply one of the best covers you can put on your jr dragster. These Jr dragster tire covers are extra wide and are USA designed and developed for maximum protection and life of your Jr Dragster tires.

Three-chamber air lumbar support by ButlerBuilt relieves lower back fatigue, maintains proper lumbar curve and is adjustable for total driver comfort and support.

Lucas Oil Slick Mist is a polymer paint gloss intensifier, which can be used on other surfaces such as glass, chrome and vinyl decals. Great for cleaning up your Junior Dragster Use Slick Mist as a traditional wax, quick detail spray or spray it on your Jr Dragster. That’s right! Just spray it on a wet or dry surface and wipe it off. Slick Mist out performs the competition and will leave your finish slicker and shinier than any product on the market, with long lasting protection. You and Slick Mist can give any machine an extreme gloss fast! CASE SHIPS FREE

Y-cable for EGT and CHT hook up for a Mychron 4 660 setup.

Full Jr dragster bearing kit includes: 4 front wheel bearings, 3 jack shaft bearings, 1 starter nut crank support bearing, 1 clutch side crank support bearing, and 2 rear axle bearings.

This 660 Pro Jr Dragster Carb top is made for HSR 42/45mm Carburetor. It features two threaded holes at the top for quick change max jets and carb clamp compatible!

415 chain break by Choo Choo

Designed for Jr. Dragsters, and Quarter Midgets Race Cars. This high performance 5W-20 synthetic blend is developed for high RPM naturally aspirated gasoline and alcohol engines.

Choo Choo helix cams for fine tuning a Choo Choo secondary. Choose your size of a one, two, or even three angle helix!

Tired of the bottom of your carburetor slipping out of the boot and costing you the round!!  This is the best kit on the market for holding your carburetor in place!  Fits in place of your current top holding mount and adds the second security of holding the bottom of the carburetor from slipping out of the boot.  Includes an air filter adapter and all hardware needed!

Lucas Penetrating Oil loosens rusted-on nuts and bolts finding its way between the tiniest of crevasses between metal parts and lubricating them. Lucas Penetrating Oil is fortified with powerful corrosion inhibitors and wetting agents that insure protection to parts exposed to the elements. Evaporation is slow, leaving a tenacious film that fights water and corrosion.

Use on: nuts, bolts, hinges, bearings, sliding doors, bicycle chains and a million other uses around the home, garage, shop and office! Stops those annoying squeaks.

Equipped with a locking pop-up tube and 360° applicator - use in any position even upside down; the product goes where you want to and you never lose the straw.

42mm Billet Carburetor Bowl by 660 Pro. Features unique tapered fuel runners to ensure top performance for your system.
*Bowl Only.*

AIM  Mychron 660 CHT sensor. Used for the 3, 4, and 5 system!

EGT Sensor for Mychron 4 660

Designed for Jr. Dragsters, and Quarter Midgets Race Cars. This high performance 5W-20 synthetic blend is developed for high RPM naturally aspirated gasoline and alcohol engines. CASE SHIPS FREE

Genuine Mikuni HSR 42/45 throttle slide.

Single Layer SFI. 3.3/1 Skeleton Gloves. Available in Orange, Lime Green, White Green.

Rebuild Kit for 33mm Mikuni carburetor. Contains:
Needle and Seat
Bowl O Ring
Top Gasket
Floats
Jet Needle

Jackshaft speed sensor

Jr Dragster Ceramic Jackshaft Bearing Kit

-Not for use with Motivational Tubing Supports

1 quart aluminum fuel cell

High Capacity, Billet, Carburetor Bowl Kit for 42mm by 660 Pro. Features unique tapered fuel runners to ensure top performance for your system. Kit includes: carb bolts, bowl gasket, bowl plug o-ring, and bowl plug.

Double Layer Skeleton Gloves SFI 3.3/5. Available in lime green, green, white, and orange.

ARC billet 7/8" stock rods.

TF-100 TIRE, 16" x 1.75" (35 PSI) Sold as set

Do you want the most efficiency possible out of your car? This is where you need to be! These things roll like none else and with the grease packed design they are made to last!
**Sold in sets of two only**

Lucas Oil Slick Mist is a polymer paint gloss intensifier, which can be used on other surfaces such as glass, chrome and vinyl decals. Great for cleaning up your junior dragster! Use Slick Mist as a traditional wax, quick detail spray or spray it on your Jr Dragster between races or rounds! That’s right! Just spray it on a wet or dry surface and wipe it off. Slick Mist out performs the competition and will leave your finish slicker and shinier than any product on the market, with long lasting protection. You and Slick Mist can give any machine an extreme gloss fast! CASE SHIPS FREE

42mm Mikuni rebuild kit

Ceramic Front Wheel Bearing Kit for Jr Dragster

-Not for use for Motivational Tubing front wheels

Jr Dragster tire hangers, installs in trailer!

These Junior Dragster Rear Wheels by 660 Pro are 8x8 3 Spoke Unfinished Do It Yourself Rims, Ready to powder coat or anodize the color of your choice. Guaranteed Run Out of 28/1000 or Less. Sold As Set. Call to order

Butlerbuilt Performance 2" Cam-Lock 5-point harness is perfect for the average racer! This harness system has a SFI16.1 rating!

MPC HI-PO BILLET MASTER CYLINDER DUAL OUTLET

MCP MASTER CYLINDER SINGLE OUTLET for Jr Dragster

Black anodized rear wheel hubs, machined to have the cleanest look with the most durability!

5 Point Camlock Harness system by Simpson
Specialized for Jr Dragster
SFI 16.2
Dual Lap Belt Adjusters
Available in steel or aluminum
Aluminum (+$100)

SFI CERTIFIED PROFESSIONAL SERIES GLOVE

The Predator Glove is constructed of Nomex®, the fabric of choice for protective gear. Individual performance leather grip-points are strategically placed to provide exceptional dexterity and natural wheel grip. Nomex's® reduced heat transfer capabilities bring an unmatched level of protection. The Predator also features an extra long bunch free gauntlet and knock out style that is sure to get you noticed. Available in much sought after White, or the always appropriate Black.

Adult Sizes: S - XL

Meets SFI 3.3/5, includes SFI tag

• Lightweight Nomex ® construction for ultimate comfort and fit
• Digital fire resistant leather with individual performance stress points
• All Nomex ® , extra long gauntlet with forearm cuff for custom fit

Two Piece jr dragster belt guard. Two pieces held together by dzus fasteners for easy access to your clutch!

ARC billet 1" x .490" flat head stroker rods

ARC billet 1" x .590" Stroker rods. 4.220 is a 1" x .5913".

These Junior Dragster Rear Wheels by 660 Pro are 8x8 3 spoke Polished Rims Ready to Bolt On. Guaranteed Run Out of 15/1000 or Less. Sold as set. Call to order

• Matte finish woven fabric
• Zippered breast pocket
• SFI tag is included on standard suits
• PANTS ONLY

With this Evac System you have no more use for a catch can on your jr dragster! This Evac is mounted to the head of the motor and runs oil right back into the block, releasing crank case pressure. With this special design, you can use your rags for something more useful than wrapping them around your air filter. That's right, NO BLOW BY!!! (Breather shown in mounted picture is NOT included. Breather Shown in kit pictures Included.)

Single Jr Dragster Tow Dolly. Call for other colors!

Jr Dragster Shut Off

Super Light Jr Dragster Pit Stands.

Jr Dragster MAGNAFUEL FUEL PUMP MIKUNI MOUNT w/ Fittings

These Rear Junior Dragster Wheels by 660 Pro are 8x8 Lightweight 3 spoke Polished and Machined for True Running Rim Guaranteed Run Out of 5/1000 or Less. Sold as Set. Call to order.

Isky cam shafts for rhino engines, all with 104 intake center line.

Jr dragster cradle for those who want to maximize your tire's lifetime!

• Matte finish woven fabric
• Zippered breast pocket
• SFI tag is included on standard suits
• JACKET ONLY

The Vortex is an SFI 3.3/5 and FIA homologated professional racing glove with Nomex® construction. FEATURES:

• SFI 3.3/5 and FIA certified
• Strategically placed wrist bone padding provides additional protection in this stressed area
• External seems and pre-curved palms provide comfort
• Tapered and pre-curved fingers and fourchettes give the driver excellent control
• Silicone palm gripper design and striking embroidered knuckle logo add to the Vortex Gloves’ appeal

660 Pro Jet Block complete with Max Jets 94-119!
AIR BLEEDS NOT INCLUDED.

The DNA Glove is a high performance driving glove using knit Nomex® that conforms to each individual driver's hands for a unique custom fit. Wear the DNA Glove for unmatched comfort and performance

• Reads to 1400º
• Laser sighted
• Back light for night use

Designed for Jr. Dragsters, and Quarter Midgets Race Cars. This high performance 5W-20 synthetic blend is developed for high RPM naturally aspirated gasoline and alcohol engines. Case of 3 x 5qt jugs. FREE SHIPPING

Quick Fill Tire Pressure Gauges - Connect to air line - fill & bleed with one gauge!

Now with back lights!!

• Reads without removing the fill chuck
• Fills twice as fast as other air pressure gauges
• Tire bleed button to release excess air pressure
• Hi-Flex 17" hose with angle chuck - ball chuck also included with All Longacre tire gauges
• Internal check valve allows use as stand alone tire gauge without air hose
• External gauge bumper - included on All Longacre air gauges
• Auto Off feature to save battery
• Easy to read to .1 psi
• Accuracy: .2 lb / .3%
• Includes hard case to protect your valuable air pressure gauge

Use this MUST HAVE tool as your regular tire pressure gauge for consistancy

Portable Ultra lightweight Polished Air Tank with Special Inlet Valve for filling:

-Filling your air tank with a tire air chuck can take 1-1/2 minutes of precious practice time!

-Add your own ¼” NPT male quick disconnect fitting to Longacre’s Deluxe Air Tanks Special inlet valve and fill the tank straight from your air compressor hose in less than 10 seconds!

-Deluxe air tanks come with a universal female coupler installed on the hose end to connect to your air chuck or inflation gauge.

The Legend II is an affordable SFI.1 rated firesuit tailored to the needs of the racer.  We have added a new distinctive styling and an attractive color combination.

This entry level FR Cotton suit includes a wrap-around around collar and three point epaulets with Simpson branding.  We have also included vertical quilting, 360 degree full arm gussets, straight leg cuffs and front pockets.  Choose from a complete range of Adult sizes.

These Rear Junior Dragster Wheels by 660 Pro offer Custom Sizes Super Lightweight 3 spoke Polished and Machined for True Running Rim. Guaranteed Run Out of 5/1000 or Less. Sold as Set
CALL FOR ORDER

Save money by buying this factory 33mm carburetor and modify it yourself!

Ceramic bearing kit for those trying to get every number out of your jr dragster! kit includes: 4 front wheel bearings, 3 jack shaft bearings, 1 starter nut crank support bearing, 1 clutch side crank support bearing, and 2 rear axle bearings.

Easily adjustable junior dragster pedal assembly. Comes with all mounting hardware. Master cylinder sold separate.

• Matte finish woven fabric
• Zippered breast pocket
• SFI tag is included on standard suits

Portable Ultra Lightweight Polished Air Tank with Analog Filler Tire Pressure Gauge

Saves time ~ quicker than dragging the air hose around the car. Tank tops off 4 tires. Exclusive special design inlet valve lets tank refill in 15 seconds or less.

Includes 0-60 psi Quick Fill Tire Gauge with 17" hose and both angle and ball chucks

Take a reading without removing the fill chuck! Connect your air line, press the lever, and fill your tires IN SECONDS! Features a bleed button for excess pressure & a large accurate Glow-In-The-Dark gauge face.

All tanks include a universal air quick-change coupler.

(Male air flow quick release not included.)

unmodified stock 42mm Mikuni flat slide carburetor. Save money and modify for alcohol yourself!

These Rear Junior Dragster Wheels by 660 Pro are 8x8 3 spoke ready to bolt on. Guaranteed Run Out of 15/1000 or Less. SOLD AS SET
CALL FOR ORDER

SFI 45.2 Jr Dragster Roll Bar Padding Head Supports.  3 Piece System. NHRA Leagal

Top notch Choo Choo fully built secondary clutch. Helix's are also available on this site for fine tuning!

Snell 2015 RJS Racing Equipment carbon fiber helmet perfect jr dragster racing.

The lightweight HANS III is now available in a Youth size. SFI 38.1 certified.

See sizing chart for recommendations - remember driver comfort is the most important factor when choosing a size.

Photo shows adult size device.

Each HANS Device is sold complete with two anchors (enough for one helmet) and matching tether. Select standard button style (left) or Quick Click system with red pull string.

The HANS III represents the third generation of injection molded HANS devices and features a contemporary approach to reducing weight. Using an all new design and polymer, the device features a hollow collar that substantially minimizes weight. Engineered reinforcements ensure an exceptionally strong structure that provides the same level of safety as every HANS device.  The reduced mass guarantees the lightest and most comfortable injection molded HANS ever.

Each HANS Device is sold complete with two anchors (enough for one helmet) and matching tether. Select standard button style (left) or Quick Click system with red pull string.

The Hybrid Sport for junior drivers! Lighter, sleek, modern and appealing with defined wings for seatbelt containment. The sliding tethers and patent pending multi-tether system enhances side to side range of movement and field of vision. The Hybrid Sport Jr. sizes are SFI 38.1 approved.

• X-Small 22-26" 4-6 Years
• Child 22-26" 7-9 Years
• Youth 26-30" 9-12 Years

Note the X-Small Child is supplied with shorter 10" FIXED tethers for the smallest of drivers.

Features

• 20% reduction in weight over earlier models
• Available with patent pending multi-tether system to enhance side to side movement
• DuPont carbon polymer construction
• Sleek, modern profile with defined wings for seatbelt containment

Dual End tethers and SAH M6 Anchors

With Seat Belt Anchor System & Quick Release Tethers & SAH D-Ring Kit
With Seat Belt Anchor System & Post Clip Tethers & SAH Post Anchors
With Seat Belt Anchor System & Dual End Tethers & SAH M6 Anchors

Hybrid Sizing Chart

• 1. Measure around chest below pectoral muscles.
• 2. Measure with driving suit. If not available add 1" to measurement.
• 3. Take measurement with tape placed against driver without any slack and without pulling the tape tight.
• 4. Once measurement has been determined refer to size chart for device size selection.

Get there with 660 Pro! Fully Built alcohol prepared 42mm carburetor by 660 Pro w/ Billet Top and High Capacity Billet Bowl w Fuel Runners.

Lithium Ion Powered Starter w/ Antigravity Battery and Starter

The Longacre Advantage

• Huge Display with Memory
  • Shows current pressure and all 4 stored tire pressures on the display at the same time
• High Accuracy
  • Accurate to .1% and reads to .1 psi
• Pyrometer Option
  • Add a tire probe and this gauge is also a precision tire pyrometer. Stores all 12 temps on the display at the same time!
• Easy to Use
  • Ergonomically designed gauge head fits comfortably in your hand
  • Triple high volume bleed buttons for fast air release
  • Swivel angle chuck and HiFlex hose - Ball chuck also included!
• Easy to Protect
  • Includes a rubber bumper for gauge protection and a hard case - Protects your investment!

The REV 2 LITE weighs in at only 1.2 lbs. / 550 grams, the REV2 LITE carries the same level of protection and certifications as the NecksGen Original and REV devices. The REV2 LITE has all the same features as the REV, but adds a new adjustable tether system, rubber grip friction pads to help you feel locked in your seat better, higher belt guides to keep everything locked in place and for multiple impact situations.
Large 3"
Medium 3"
Small 2"

SFI 38.1 certified, FIA certification available. The Hybrid Sport from Simpson features a light-weight design using DuPont® carbon/polymer construction and provides maximum comfort and maneuverability with superior strength. Hybrids come race ready. The trusted low profile design disappears into the seat when worn and allows for easy in and out of the race car, eliminating the danger of becoming caught in other gear. The protection stays with the racer during multiple impact, flips and rolls.

Features
SFI Certification- Standard.
FIA Certification - Available: call for details 800.654.7223

• Available with patent pending multi-tether system to enhance side to side movement
• DuPont carbon polymer construction
• Sleek, modern profile with defined wings for seatbelt containment

• Hybrid Sizing Chart

  • 1. Measure around chest below pectoral muscles.
  • 2. Measure with driving suit. If not available add 1" to measurement.
  • 3. Take measurement with tape placed against driver without any slack and without pulling the tape tight.
  • 4. Once measurement has been determined refer to size chart for device size selection.

Full mychron 5 660 kit. This is the latest AiM Jr Dragster tachometer and comes with everything pictured.

Top notch 45mm Choo Choo carburetor by Lynn Haddock Ltd with a Dial-A-Jet for maximum fuel flow and performance! Comes with Choo Choo billet top and billet bowl. Own the best of the best.

Top of the line fully built Choo Choo outlaw primary clutch.

Full Choo Choo outlaw clutch package for those who want top of the line performance! Comes with two belts and two helix's. Helix's are also available here for fine tuning your setup!

Blossom super rhino 2 bore sizes from 3.140 to 3.550. Comes with fully built carburetor, intake manifold, and header. Call for details, specs, and options.